Solutions · Multi-Analyte Visibility

Every analyte in the run, at once.

A capability of the Calibration Intelligence dashboard: methods with dozens or hundreds of analytes are evaluated and displayed together, so a failing curve cannot hide in compound forty-seven.

The problem

Single-analyte review does not scale.

Multi-residue and panel methods put enormous target lists behind a screen built to show one curve at a time. The longer the list, the less each compound is actually seen.

01

Hundreds of compounds, one window

Pesticide panels, PFAS lists and tox screens run through an interface designed for a single curve.

02

Fatigue sets the error rate

By the fortieth compound, attention is the scarcest reagent in the lab.

03

Context gets lost

Reviewed one at a time, analytes cannot be compared, and a pattern that touches the whole run goes unseen.

With WLTR

What multi-analyte visibility delivers

The whole run on one screen

Every analyte’s calibration, status and best fit, visible together in the Calibration Intelligence dashboard.

Consistent analyte names

Every analyte maps to a consistent name, so long target lists can be trended across runs and instruments.

Patterns, not points

Drift that touches the whole run shows up as a pattern instead of forty separate findings.

Exceptions rise to the top

Passing analytes clear out of the way. Failures and borderline curves surface first.

Equal scrutiny, every compound

The last analyte on the list gets the same evaluation as the first.

One record for the batch

The run is approved on evidence that stays with the batch record.

See it work

The whole run, reviewed as one.

Every compound in the method, with its calibration curve, its standards and every candidate model, on one screen. Select any analyte to see its curve and chromatograms. Exceptions are flagged, so review starts where attention is needed instead of at compound one.

Try it yourself

See what a passing r² can hide in your own calibration.

Enter a curve, or load a sample, and see which levels actually back-calculate inside your acceptance window. Then work through a simulated LC-MS/MS quantitation review, laid out the way your data system shows it.

Simulation

This tool does not run WLTR’s engine, patented methodology or evaluation criteria. It applies eight standard least-squares calibration models and textbook acceptance rules. The batch and chromatograms are fictional. Everything is calculated in your browser, and nothing you enter is sent or stored.

Data
Calibration levels
#ConcentrationResponseRemove

Response can be a peak area or an area ratio to the internal standard. You can paste two columns straight from a spreadsheet into any cell.

r²
–
Levels in window
–

Calibration curve
Back-calculated accuracy by level

Each bar is a level’s error after back-calculation. The shaded band is your acceptance window.

Standard models compared (select a row)
Modelrr²Adj. r²Levels in windowWorst errorStatus

Simulation for illustration only. Sample datasets, the batch, chromatograms and names are fictional. Results on this page are not WLTR output, are not a method validation, and should not be used to accept or reject laboratory data.

Size your run

What one screen is worth on a full method.

Enter your own method. The calculator shows how much work a single run holds, and how much review time comes back when analysts start at the exceptions instead of at compound one.

Your method

Estimates only. Change any value to model your lab.

min
By hand, one analyte at a time
%
Flagged as exceptions
Curves on one screen0
Model fits computed0
Back-calculated checks0
Hand review per run0 h
Review hours returned per week0 h

Review time per run

The same run, reviewed two ways. Each block is one twentieth of the hand-review time.

Share of review time returned0%

Illustrative. Based only on the values you enter. WLTR does not remove analyst review; it points it at the curves that need it, with every model and analyte already evaluated.

One verification layer

Four solutions. One layer.

Each solution is one view of the same verification layer. Together they turn raw instrument output into a verified, traceable, QA-approved calibration record.

See the whole run, not one curve.

We find operational inefficiencies & design the systems that eliminate it.